Automation

Websters definition: automatically controlled operation of an apparatus, process, or system by mechanical or electronic devices that take the place of human organs of observation, effort, and decision

Some Automation terminology...

• AC input module: This is a module that converts a real-world AC input signal to the logic level required by the PLC processor.
• AC output module: Module that converts the processor logic level to an AC output signal to control a real-world device.
• Accumulated value: Applies to the use of timers and counters. The accumulated value is the present count or time.
• Accuracy: The deviation between the actual position and the theoretical position.
• Actuator: Output device normally connected to an output module. An example would be an air valve and cylinder.
• Address: Number used to specify a storage location in memory.
• Ambient temperature: Temperature that naturally exists in the environment. For example, the ambient temperature of a PLC in a cabinet near a steel furnace is very high.
• Analog: Signal with a smooth range of possible values. For example, a temperature that could vary between 60 and 300 degrees would be analog in nature.
• ANSI: American National Standards Institute.
• ASCII: American Standard Code for Information Interchange. A coding system used to represent letters and characters. Seven-bit ASCII can represent 128 different combinations. Eight-bit ASCII (extended ASCII) can represent 256 different combinations.
• Asynchronous communications: Method of communications that uses a series of bits to send data between devices. There is a start bit, data bits (7 or 8), a parity bit (odd, even none, mark, or space), and stop bits (1, 1.5, or 2). One character is transmitted at a time. RS-232 is the most common.

• Backplane: Bus in the back of a PLC chassis. It is a printed circuit board with sockets that accept various modules.
• Baud rate: Speed of serial communications. The number of bits per second transmitted. For example, RS-232 is normally used with a baud rate of 9600. This would be about 9600 bits per second. It takes about 10 bits in serial to send an ASCII character so that a baud rate of 9600 would transmit about 960 characters per second.
• BEUG (BITBUS European Users Group): BEUG is a nonprofit organization devoted to spreading the BITBUS technology and organizing a basic platform where people using BITBUS can share application experiences.
• Binary: Base two number system. Binary is a system in which ones and zeros are used to represent numbers.
• Binary-coded decimal (BCD): A number system. Each decimal number is represented by four binary bits. For example, the decimal number 967 would be represented by 1001 0110 0111 in BCD.
• Bit: Binary digit. The smallest element of binary data. A bit will be either a zero or a one.
• BITBUS: It is one of the most widely used fieldbuses. It was promoted as a standard in 1990 by a special committee of the IEEE (standard IEEE-1118 1990).
• Boolean: Logic system that uses operators such as AND, OR, NOR, and NAND. This is the system that is utilized by PLCs, although it is usually made invisible by the programming software for the ease of the programmer.
• Bounce: This is an undesirable effect. It is the erratic make and break of electrical contacts.
• Branch: Parallel logic path in a ladder diagram.
• Byte: Eight bits or two nibbles. (A nibble is 4 bits.)

• Cascade: Programming technique that is used to extend the range of timers and counters.
• CENELEC: European Committee for Electrotechnical Standardization. It develops standards which cover dimensional and operating characteristics of control components.
• Central processing unit (CPU): Microprocessor portion of the PLC. It is the portion of the PLC that handles the logic.
• Color mark sensor: Sensor that was designed to differentiate between two different colors. They actually differentiate on the basis of contrast between the two colors.
• Complement: The complement is the inverse of a digital signal.
• CMOS (complementary metal-oxide semiconductor): Integrated circuits that consume very little power and also have good noise immunity.
• Compare instruction: PLC instruction that is used to test numerical values for equal, greater than, or less than relationships.
• Contact: Symbol used in programming PLCs. Used to represent inputs. There are normally open and normally closed contacts. Contacts are also the conductors in electrical devices such as starters.
• Contactor: Special-purpose relay that is used to control large electrical current.
• CSA (Canadian Standards Organization): Develops standards, tests products and provides certification for a wide variety of products.
• Current sinking: Refers to an output device (typically an NPN transistor) that allows current flow from the load through the output to ground.
• Current sourcing: Output device (typically a PNP transistor) that allows current flow from the output through the load and then to ground.
• Cyclic Redundancy Check (CRC): A calculated value, based on the content of a communication frame. It is inserted in the frame to enable a check of data accuracy after receiving the frame across a network. BITBUS uses the standard SDLC CRC.

• Dark-on: Refers to a photosensor's output. If the sensor output is on when no object is sensed, it is called a dark-on sensor.
• Data highway: This is a communications network that allows devices such as PLCs to communicate. They are normally proprietary, which means that only like devices of the same brand can communicate over the highway.
• Data table: A consecutive group of user references (data) of the same size that can be accessed with table read/write functions.
• Debugging: Process of finding problems (bugs) in any system.
• Diagnostics: Devices normally have software routines that aid in identifying and finding problems in the device. They identify fault conditions in a system.
• Digital output: An output that can have two states: on or off. These are also called discrete outputs.
• Distributed processing: The concept of distributed processing allows individual discrete devices to control their area and still communicate to the others via a network. The distributed control takes the processing load off the "host" system.
• Documentation: Documentation is descriptive paperwork that explains a system or program. It describes the system so that the technician can understand, install, troubleshoot, maintain, or change the system.
• Downtime:The time a system is not available for production or operation is called downtime. Downtime can be caused by breakdowns in systems.

• EEPROM: Electrically erasable programmable read only memory.
• Energize: Instruction that causes a bit to be a one. This turns an output on.
• Examine-off: Contact used in ladder logic. It is a normally closed contact. The contact is true (or closed) if the real-world input associated with it is off.
• Examine-on: Contact used in ladder logic programming. Called a normally open contact. This type of contact is true (or closed) if the real-world input associated with it is on.
• Expansion rack: A rack added to a PLC system when the application requires more modules than the main rack can contain. A remote rack is sometimes used to permit I/O to be remotely located from the main rack.

• False: Disabled logic state (off).
• Fault: Failure in a system that prevents normal operation of a system.
• Firmware: A series of instructions contained in read-only memory (ROM) that are used for the operating system functions. Some manufacturers offer upgrades for PLCs. This is often done by replacing a ROM chip. Thus the combination of software and hardware lead to it being called firmware.
• Flowchart: Used to make program design easier.
• Force: Refers to changing the state of actual I/O by changing the bit status in the PLC. In other words, a person can force an output on by changing the bit associated with the real-world output to a 1. Forcing is normally used to troubleshoot a system.
• Frame: Packet of bits that will be transmitted across a network. A frame contains a header, user data and an end of frame. The frame must contain all the necessary information to enable the sender and receiver(s) of the communication to decode the user's data and to ensure that this data is right.
• Full duplex: Communication scheme where data flows in both directions simultaneously.

• Ground: Direct connection between equipment (chassis) and earth ground.

• Half duplex: Communication scheme where data flows in both directions but in only one direction at a time.
• Hard contacts: Physical switch connections.
• Hard copy: Printed copy of computer information.
• HDLC (High-level Data Link Control): Standard protocol of communication oriented in message transmission (frames). The user's data field in an HDLC-frame can be of a free number of bits. The SLDC is a subset of the HDLC that defines the whole protocol in more detail and is byte-oriented.
• Hexadecimal: Numbering system that utilizes base 16.
• Host computer: One to which devices communicate. The host may download or upload programs, or the host might be used to program the device. An example would be a PLC connected to a microcomputer. The host (microcomputer) "controls" the PLC by sending programs, variables, and commands. The PLC controls the actual process but at the direction and to the specifications of the host.
• Hysteresis: A dead band that is purposely introduced to eliminate false reads in the case of a sensor. In an encoder hysteresis would be introduced in the electronics to prevent ambiguities if the system happens to dither on a transition.

• IEC (International Electrotechnical Commission): Develops and distributes recommended safety and performance standards.
• IEEE: Institute of Electrical and Electronic Engineers.
• Image table: Area used to store the status of input and output bits.
• Incremental: This term typically refers to encoders. Encoders provide logic states of 0 and 1 for each successive cycle of resolution.
• Instruction set: Instructions that are available to program the PLC.
• Intelligent I/O: PLC modules that have a microprocessor built in. An example would be a module that would control closed-loop positioning.
• Interfacing: Connection of a PLC to external devices.
• I/O (input/output): Used to speak about the number of inputs and outputs that are needed for a system, or the number of inputs and outputs that a particular programmable logic controller can handle.
• IP rating: Rating system established by the IEC that defines the protection offered by electrical enclosures. It is similar to the NEMA rating system.
• Isolation: Used to segregate real-world inputs and outputs from the central processing unit. Isolation assures that even if there is a major problem with real-world inputs or outputs (such as a short), the CPU will be protected. This isolation is normally provided by optical isolation.

• K: Abbreviation for the number 1000. In computer language it is equal to two to the tenth, or 1024.
• Keying: Technique to ensure that modules are not put in the wrong slots of a PLC. The user sets up the system with modules in the desired slots. The user then keys the slots to assure that only a module of the correct type can be physically installed.

• Ladder diagram: Programmable controller language that uses contacts and coils to define a control sequence.
• LAN: See Local area network.
• Latch: An instruction used in ladder diagram programming to represent an element that retains its state during controlled toggle and power outage.
• Leakage current: Small amount of current that flows through load-powered sensors. The small current is necessary for the operation of the sensor. The small amount of current flow is normally not sensed by the PLC input. If the leakage is too great a bleeder resistor must be used to avoid false inputs at the PLC.
• LED (light-emitting diode): A solid-state semiconductor that emits red, green, or yellow light or invisible infrared radiation.
• Light-on sensor: This refers to a photosensor's output. If the output is on when an object is sensed, the sensor is a light-on sensor.
• Linear output: Analog output.
• Line driver: A line driver is a differential output driver intended for use with a differential receiver. These are usually used where long lines and high frequency are required and noise may be a problem.
• Line-powered sensor: Normally, three-wire sensors, although four-wire sensors also exist. The line-powered sensor is powered from the power supply. A separate wire (the third) is used for the output line.
• Load: Any device that current flows through and produces a voltage drop.
• Load-powered sensor: A load-powered sensor has two wires. A small leakage current flows through the sensor even when the output is off. The current is required to operate the sensor electronics.
• Load resistor: A resistor connected in parallel with a high-impedance load to enable the output circuit to output enough current to ensure proper operation.
• Local area network (LAN): A system of hardware and software designed to allow a group of intelligent devices to communicate within a fairly close proximity.
• Lockout: The placement of a lockout device on an energy isolating device, in accordance with an established procedure, to ensure that the energy isolating device and the equipment being controlled cannot be operated until the lockout device is removed.
• Lockout device: A device that utilizes a positive means such as a lock, either key or combination type, to hold an energy isolating device in the safe position and prevent the energizing of a machine or equipment.
• LSB: Least significant bit.

• Machine language: Control program reduced to binary form.
• MAP (manufacturing automation protocol): "Standard" developed to make industrial devices communicate more easily. Based on a seven-layer model of communications.
• Master: The master on a network is the device that controls communication traffic. The master of a network usually polls every slave to check if it has something to transmit. In a master-slave configuration, only the active master can place a message on the bus. The slave can reply only if it receives a frame from the master that contains a logical token that explicitly enables the slave to reply.
• Master control relay (MCR): Hardwired relay that can be deenergized by any hardwired series-connected switch. Used to deenergize all devices. If one emergency switch is hit it must cause the master control relay to drop power to all devices. There is also a master control relay available in most PLCs. The master control relay in the PLC is not sufficient to meet safety requirements.
• Memory map: Drawing showing the areas, sizes, and uses of memory in a particular PLC.
• Microsecond: A microsecond is one millionth (0.000001) of a second.
• Millisecond: A millisecond is one thousandth (.001) of a second.
• Mnemonic codes: Symbols designated to represent a specific set of instructions for use in a control program. An abbreviation given to an instruction: usually an acronym that is made by combining the initial letters or parts of words.
• MSB: Most significant bit.

• NEMA (National Electrical Manufacturers Association): Develops standards that define a product, process, or procedure. The standards consider construction, dimensions, tolerances, safety, operating characteristics, electrical rating and so on. They are probably best known for their rating system for electrical cabinets.
• Network: System that is connected to devices or computers for communication purposes.
• Node: Point on the network that allows access.
• Noise: Unwanted electrical interference in a programmable controller or network. It can be caused by motors, coils, high voltages, welders, and so on. It can disrupt communications and control.
• Nonretentive coil: A coil that will turn off upon removal of applied power to the CPU.
• Nonretentive timer: Timer that loses the time if the input enable signal is lost.
• Nonvolatile memory: Memory in a controller that does not require power to retain its contents.
• NOR: The logic gate that results in zero unless both inputs are zero.
• NOT: The logic gate that results in the complement of the input.

• Octal: Number system based on the number 8, utilizing numbers 0 through 7.
• Off-delay timer: This is a type of timer that is on immediately when it receives its input enable. It turns off after it reaches its preset time.
• Off-line programming: Programming that is done while not attached to the actual device. For example, a PLC program can be written for a PLC without being attached. The program can then be downloaded to the PLC.
• On-delay timer: Timer that does not turn on until its time has reached the preset time value.
• One-shot contact: Contact that is only on for one scan when activated.
• Operating system: The fundamental software for a system that defines how it will store and transmit information.
• Optical isolation: Technique used in I/O module design that provides logic separation from field levels.
• OR: Logic gate that results in 1 unless both inputs are 0.

• Parallel communication: A method of communications where data is transferred on several wires simultaneously.
• Parity: Bit used to help check for data integrity during a data communication.
• Peer-to-peer: This is communication that occurs between similar devices. For example, two PLCs communicating would be peer-to-peer. A PLC communicating to a computer would be device-to-host.
• PID (Proportional, integral, derivative) control: Control algorithm that is used to closely control processes such as temperature, mixture, position, and velocity. The proportional portion takes care of the magnitude of the error. The integral takes care of small errors over time. The derivative compensates for the rate of error change.
• PLC: Programmable logic controller.
• Programmable controller: A special-purpose computer. Programmed in ladder logic. It was also designed so that devices could be easily interfaced with it.
• Pulse modulated: Turning a light source on and off at a very high frequency. In sensors the sending unit pulse modulates the light source. The receiver only responds to that frequency. This helps make photo-sensors immune to ambient lighting.
• PPR (Pulses per revolution): This refers to the number of pulses an encoder produces in one revolution.

• Quadrature: Two output channels out of phase with each other by 90 degrees.

• Rack: PLC chassis. Modules are installed in the rack to meet the user's need.
• Radio frequency (RF): Communications technology in which there is a transmitter/receiver and tags. The transmitter/ receiver can read or write to the tags. There are active and passive tags available. Active tags are battery powered. Passive tags are powered from the RF emitted from the transmitter. Active tags have a much wider range of communication. Either tag can have several K of memory.
• RAM (random access memory): Normally considered user memory.
• Register: Storage area. It is typically used to store bit states or values of items such as timers and counters.
• Repeatability: The ability to repeat movements or readings. For a robot it would be how accurately it would return to a position time after time. Repeatability is unrelated to resolution and is usually 3 to 10 times better than accuracy.
• Resolution: A measure of how closely a device can measure or divide a quantity. For example, in an encoder resolution would be defined as counts per turn. For an analog to digital card it would be the number of bits of resolution. For example, for a 12-bit card the resolution would be 4096.
• Retentive coil: A coil that will remain in its last state, even though power was removed.
• Retentive timer: Timer that retains the present count even if the input enable signal is lost. When the input enable is active again, the timer begins to count again from where it left off.
• Retroreflective: Photosensor that sends out a light which is reflected from a reflector back to the receiver (the receiver and emitter are in the same housing). When an object passes through it breaks the beam.
• RF (radio frequency): See radio frequency.
• ROM (read-only memory): This is operating system memory. ROM is nonvolatile. It is not lost when the power is turned off.
• RS-232: Common serial communications standard. This standard specifies the purpose of each of 25 pins. It does not specify connectors or which pins must be used.
• RS-422 and RS-423: Standards for two types of serial communication. RS-422 is a balanced serial mode. This means that the transmit and receive lines have their own common instead of sharing one like RS-232. Balanced mode is more noise immune. This allows for higher data transmission rates and longer transmission distances. RS-423 uses the unbalanced mode. Its speeds and transmission distances are much greater than RS-232 but less than RS-422.
• RS-449: Electrical standard for RS-422/RS-423. It is a more complete standard than the RS-232. It specifies the connectors to be used also. RS-485: Similar to the RS-422 standard. Receivers have additional sensitivity which allows for longer distances and more communication drops. Includes some extra protection for receiver circuits.
• Rung: Group of contacts that control one or more outputs. In a ladder diagram it is the horizontal lines on the diagram.

• Scan time: Amount of time it takes a programmable controller to evaluate a ladder diagram. The PLC continuously scans the ladder diagram. The time it takes to evaluate it once is the scan time. It is typically in the low-millisecond range.
• SDLC: Serial Data Link Control, subset of the HDLC used in a large number of communication systems like Ethernet, ISDN, BITBUS, and others. This protocol defines the structure of the frames and the values of a number of specific fields in these frames.
• Sensitivity: Refers to a device's ability to discriminate between levels. If it's a sensor it would relate to the finest difference it could detect. If it were an analog module for a PLC, it would be the smallest change it could detect.
• Sensor: Device used to detect change. Normally it is a digital device. The outputs of sensors change state when they detect the correct change. Sensors can be analog or digital in nature. They can also be purchased with normally closed or normally open outputs.
• Sequencer: Instruction type that is used to program a sequential operation.
• Serial communication: Sending of data one bit at a time. The data is represented by a coding system such as ASCII.
• Slave: On a master-slave configured network, there is usually one master and several slaves. The slaves are nodes of the network that can transmit informations to the master only when they are polled (called) from it. The rest of the time a slave never transmits anything.
• Speech modules: Used by a PLC to output spoken messages to operators. The sound is typically digitized human speech stored in the module's memory. The PLC requests the message number to play it.

• Tagout: The placement of a tagout device on an energy isolating device, in accordance with an established procedure, to indicate that the energy isolating device and the equipment being controlled may not be operated until the tagout device is removed.
• Tagout device: A prominent warning device, such as a tag and a means of attachment, which can be securely fastened to an energy isolating device in accordance with an established procedure, to indicate that the energy isolating device and the equipment being controlled may not be operated until the tagout device is removed.
• Thermocouple: A thermocouple is a sensing transducer. It changes a temperature to a current. The current can then be measured and converted to a binary equivalent that the PLC can understand.
• Thumbwheel: Device used by an operator to enter a number between 0 and 9. Thumbwheels are combined to enter larger numbers. Thumbwheels typically output BCD numbers to a device.
• Timer: Instruction used to accumulate time until a certain value is achieved. The timer then changes its output state.
• TOP (technical and office protocol): Communication standard that was developed by Boeing. Based on the contention access method. The MAP standard is meant for the factory floor and TOP is meant for the office and technical areas.
• Transitional contact: Contact that changes state for one scan when activated.
• True: This is the enabling logic state. Generally associated with a "one" or "high" state.

• UL (Underwriters Laboratory): Organization that operates laboratories to investigate systems with respect to safety.
• User memory: Memory used to store user information. The user's program, timer/counter values, input/output status, and so on, are all stored in user memory.

• Volatile memory: Memory that is lost when power is lost.

• Watchdog timer: Timer that can be used for safety. For example, if there is an event or sequence that must occur within a certain amount of time, a watchdog timer can be set to shut the system down in case the time is exceeded.
• Word: Length of data in bits that a microprocessor can handle. For example, a word for a 16-bit computer would be 16 bits long, or two bytes. A 32-bit computer would have a 32-bit word.